Soluzioni Tecnologiche
Innovation is the heart of our philisophy. Our R&D department works day after day to offer our customers innovative and efficient techological solutions, which ensure perfect washing results with a special attention to consumption and environmental sustainability.
BT - BREAK TANK SYSTEM
The Break Tank system is an innovation by Hoonved introduced in 2008 to guarantee excellent rinse results.
This special system:
- ensures that rinsing occurs at a constant pressure and temperature
- prevents washing cycles without water
- prevents boiler water backflow towards the mains water supply, preventing contamination
Benefits
Sparkling
results
GLASSES AND DISHES
BETTER
DRYING
MAXIMUM
HYGIENE
Standard Machine
- Wash arm - upper
- Rinse arm - upper
- Rinse arm - lower
- Wash arm - lower
- Wash pump
- Tank
- Tank heater
- Boiler heater
- Boiler
- Inlet valve
Machine with Break Tank
- Wash arm - upper
- Boiler level pressure switch
- Air gap
- Rinse arm - upper
- Rinse arm - lower
- Wash arm - lower
- Wash pump
- Rinse pump
- Tank
- Tank heater
- Boiler
- Boiler heater
- Inlet valve
Standard Machine
1. Decreasing temperature
2. Variable pressure (net water)
3. Possible water contamination
Break Tank Machine
1. Steady temperature
2. Steady pressure
3. Air gap - no backflow towards the water supply
RCC - HEAT RECOVERY UNIT
The exclusive RCC system is based on the use of heat/steam generated during the wash/rinse cycle to pre-heat the water input into the machine. The system condenses the steam generated during the washing cycle ensuring an improved working environment and energy savings.
Benefits
Energy
savings
Does not contain filters
and is maintenance free
Faster
drying times
No steam or humidity
in the room
HP - HEAT PUMP
The heat pump is a machine which can transfer heat from a low-temperature body to a high-temperature body. This heat transfer allows you to obtain more energy than it uses for its operation, ensuring significant savings on electric consumption and an improvement in the quality of the work environment.
Benefits
Approximately 40% reduction in the energy used to heat and maintain
the temperature of the washing tank
(with no heating element in the tank)
Air emission with an average temperature
of less than 25°C
No steam
when door is opened
Less humidity
in the washing room
Temperature control effect extending heat pump operation beyond the cycle
Faster drying
Function scheme
- Compression: the fluid input from the evaporator (low pressure gaseous form) is pressurised. The fluid is heated in the compressor and the temperature increases.
- Condensation: the high-temperature fluid in the condenser releases heat passing from a gas to a liquid state. The heat released is used to heat water in the utensil washer tank.
- Expansion: as the cooling fluid passes through the expansion valve, it cools down and partly turns into vapour.
- Evaporation: the fluid, passing through the evaporator, absorbs heat and evaporates completely (gaseous state). Through this process, the heat pump recovers the latent heat generated by the utensil washer during operation, and eliminates the release of steam at the end of the cycle, thus reducing electricity consumption.
A. Steam (warm air from the machine)
B. Exhausted air 18-20 °C
C-D. Air from the room
E. Wash tank
HPRS - SPEED PROPORTIONAL RINSE SYSTEM
The HPRS system, which can be installed on our entire range of rack-conveyor dishwashers, allows you to adjust the required amount of water for rinsing based on the conveyor speed, ensuring significant savings in water, energy and detergent consumption (up to 30%!).
Benefits
saving on water consumption (-30%)
saving on energy consumption (-30%)
Saving on detergent consumption (-30%)
eco-friendly technology
- Prewash
- Wash
- Power rinse
- Final rinse
- Dryer
- 1st speed
- 2nd speed
AP - FRESH WATER SYSTEM
This exclusive system allows you to wash glasses, ice cream pans and kitchen utensils with fresh water at every cycle. This occurs in two phases:
- At the end of the wash, all the water in the tank is eliminated by the drain pump. Then, the rinse phase starts.
- The new wash cycle starts with the rinse water which collects in the tank and the addition of fresh water.
Thus, it is possible to wash dishes with water that has been almost completely renewed and achieve washing results that are significantly better than those obtained with traditional machines.
To limit consumption, the water in the tank is reduced to a minimum and the water jets wash the glasses at a pressure that is 5 times higher than normal.
Benefits
fresh water at every cycle
better wash results on glasses compared to traditional machines
elimination of odours
glasses and pans
perfect hygiene
The ultra-fine filtering system
makes it possible to eliminate any traces of fruit that traditional machines cannot remove
Standard System
- Tank
- Boiler
Fresh water system
- Tank
- Boiler
- Minore quantità di acqua in vasca (riduzione dei consumi di acqua, prodotti, energia)
- Assenza della resistenza in vasca per una migliore pulizia interna
- Pompa di scarico per espellere tutta l’acqua del lavaggio
- Non necessita del troppopieno
- Risciacquo volumetrico (non a tempo) e ricambio totale dell’acqua ad ogni ciclo
WATER TREATMENT - REVERSE OSMOSIS SYSTEM
Reverse osmosis is the process which occurs between two solutions with different concentrations when molecules of water are forced to pass from the more concentrated solution to the less concentrated one. In this way, the water obtained is purified by 98% and can be used to wash glasses with visible results in the drying phase.
Benefits
Superior washing results compared to traditional machines:
ultra-bright glasses with no water marks.
Natural drying in a few minutes
No more hand drying of glasses and related accidents
breakages, injuries
Reverse osmosis must always be combined with a BT (Break Tank) which ensures rinsing occurs at a constant temperature and pressure. The results are visibly improved compared to those obtained with traditional machines, which are affected by the variation in water temperature and pressure.
- the installation of an automatic softener with volumetric valve connected to the mains water supply if the water temperature is over 20°C. The volumetric system reduces maintenance costs because regeneration occurs exclusively on how much water is actually consumed.
- to use specific products for osmosis because standard products could be too aggressive
- to use inclined glasses baskets to facilitate drying and improve the rinsing phase.
- input water temperature: 5°C – 25°C.
WATER TREATMENT - SOFTENERS
The softener is an essential accessory for treating hard water in order to eliminate traces of calcium and magnesium from within it and ensure excellent washing results. Hoonved has a complete range of automatic and volumetric softeners. Compared to traditional softeners that regenerate the water based on programming, with this type of softener, regeneration only occurs based on how much water is actually consumed. This results in significant savings in operating costs (lower energy and detergent consumption).
Benefits
lower energy consumption
lower detergent consumption
savings on management costs
excellent washing results
